howtos:admin:install_and_administer_a_virtual_machine_vm
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
howtos:admin:install_and_administer_a_virtual_machine_vm [2009/12/22 12:50] shona.weldon |
howtos:admin:install_and_administer_a_virtual_machine_vm [2024/02/22 19:02] (current) marcus.williams |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Installing and Configuring a VM for whatIf? ====== | ====== Installing and Configuring a VM for whatIf? ====== | ||
| + | **❌ CONTENT NOT MIGRATED (LEFT BEHIND) TO GURU** | ||
| ===== Setting up Networking on a new VM ====== | ===== Setting up Networking on a new VM ====== | ||
| Line 8: | Line 9: | ||
| * login as root (pword What1f?) | * login as root (pword What1f?) | ||
| * Open the Networking - click on the red hat/system settings/network | * Open the Networking - click on the red hat/system settings/network | ||
| - | * Probe the machine | + | * Probe the machine by: |
| * select first (only) profile and click on edit button | * select first (only) profile and click on edit button | ||
| * click on hardware device tab | * click on hardware device tab | ||
| Line 18: | Line 19: | ||
| * Take note of the ip address (you'll need it for the next steps in host only mode) | * Take note of the ip address (you'll need it for the next steps in host only mode) | ||
| * Go to the devices tab, double click the eth0 | * Go to the devices tab, double click the eth0 | ||
| - | * Record the static ip address, probably something like: 192.68.80.200 | + | * Record the static ip address, probably something like: 192.168.80.200 |
| * Logout and reboot the machine | * Logout and reboot the machine | ||
| Line 24: | Line 25: | ||
| How to get it into nat mode: | How to get it into nat mode: | ||
| * Make the VMnet8 network connection configuration use DHCP to obtain addres | * Make the VMnet8 network connection configuration use DHCP to obtain addres | ||
| - | * Set the Devices/Network Adaptor on the VM to NAT | + | * Set the Devices/Network Adaptor on the VM to NAT in the "Settings" of the outer shell of the VM Player |
| * In the networking of the VM setup the IP address to come from DHCP | * In the networking of the VM setup the IP address to come from DHCP | ||
| * Uncheck the "Automatically obtain DNS information from provider | * Uncheck the "Automatically obtain DNS information from provider | ||
| Line 35: | Line 36: | ||
| ==== Setup network on host ==== | ==== Setup network on host ==== | ||
| + | === Windows XP === | ||
| * On the host machine (windows side) From "Start" menu choose "Connect To/Show all Connections" | * On the host machine (windows side) From "Start" menu choose "Connect To/Show all Connections" | ||
| + | |||
| + | === Windows Vista & Windows 7 === | ||
| + | * On the host machine (windows side) From "Start" menu choose "Network and Internet" | ||
| + | then choose "Network and Sharing Center" and look in the "View your active networks" section of the page | ||
| + | |||
| + | === On either system continue with: === | ||
| * Choose VMNet1 for host only mode (VMnet8 for NAT mode) connection and look at the properties (right click properties) | * Choose VMNet1 for host only mode (VMnet8 for NAT mode) connection and look at the properties (right click properties) | ||
| * If you intend to use VMnet1 (which is the default) disable VMnet8 | * If you intend to use VMnet1 (which is the default) disable VMnet8 | ||
| - | * Double click "Internet Protocol (TCP/IP)" | + | * Double click "Internet Protocol (TCP/IP)" (on Vista and windows 7 choose TCP/IPv4) |
| * Make sure the first 3 parts of the ip address match that of your VM but not the last | * Make sure the first 3 parts of the ip address match that of your VM but not the last | ||
| * If VM is in host only mode adjust the host side here (use this option by default) | * If VM is in host only mode adjust the host side here (use this option by default) | ||
| Line 49: | Line 57: | ||
| * Startup the VM you don't need to login | * Startup the VM you don't need to login | ||
| * Use putty to connect to newName-ux and login as root | * Use putty to connect to newName-ux and login as root | ||
| + | * If you can't get that to work check the host name settings inside the VM networking | ||
| + | * Add an entry for newName-ux and the corresponding ip address to the host machine's hosts file under (C:\Windows\System32\drivers\etc) | ||
| + | * To modify hosts file, you will need to run editor program as an administrator and hope the hosts file from inside that program | ||
| + | * If you still can't get it to work you can use the ip address of the machine which we recorded at the beginning | ||
| + | * IP address is probably 192.168.80.200 | ||
| ==== Setting up Accounts on a new VM ===== | ==== Setting up Accounts on a new VM ===== | ||
howtos/admin/install_and_administer_a_virtual_machine_vm.1261486207.txt.gz · Last modified: 2009/12/22 12:50 by shona.weldon
Page Tools
