This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
howtos:admin:install_and_administer_a_virtual_machine_vm [2010/02/05 21:58] shona.weldon |
howtos:admin:install_and_administer_a_virtual_machine_vm [2024/02/22 19:02] (current) marcus.williams |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== Installing and Configuring a VM for whatIf? ====== | ====== Installing and Configuring a VM for whatIf? ====== | ||
+ | **❌ CONTENT NOT MIGRATED (LEFT BEHIND) TO GURU** | ||
===== Setting up Networking on a new VM ====== | ===== Setting up Networking on a new VM ====== | ||
Line 18: | Line 19: | ||
* Take note of the ip address (you'll need it for the next steps in host only mode) | * Take note of the ip address (you'll need it for the next steps in host only mode) | ||
* Go to the devices tab, double click the eth0 | * Go to the devices tab, double click the eth0 | ||
- | * Record the static ip address, probably something like: 192.68.80.200 | + | * Record the static ip address, probably something like: 192.168.80.200 |
* Logout and reboot the machine | * Logout and reboot the machine | ||
Line 24: | Line 25: | ||
How to get it into nat mode: | How to get it into nat mode: | ||
* Make the VMnet8 network connection configuration use DHCP to obtain addres | * Make the VMnet8 network connection configuration use DHCP to obtain addres | ||
- | * Set the Devices/Network Adaptor on the VM to NAT | + | * Set the Devices/Network Adaptor on the VM to NAT in the "Settings" of the outer shell of the VM Player |
* In the networking of the VM setup the IP address to come from DHCP | * In the networking of the VM setup the IP address to come from DHCP | ||
* Uncheck the "Automatically obtain DNS information from provider | * Uncheck the "Automatically obtain DNS information from provider | ||
Line 35: | Line 36: | ||
==== Setup network on host ==== | ==== Setup network on host ==== | ||
+ | === Windows XP === | ||
* On the host machine (windows side) From "Start" menu choose "Connect To/Show all Connections" | * On the host machine (windows side) From "Start" menu choose "Connect To/Show all Connections" | ||
+ | |||
+ | === Windows Vista & Windows 7 === | ||
+ | * On the host machine (windows side) From "Start" menu choose "Network and Internet" | ||
+ | then choose "Network and Sharing Center" and look in the "View your active networks" section of the page | ||
+ | |||
+ | === On either system continue with: === | ||
* Choose VMNet1 for host only mode (VMnet8 for NAT mode) connection and look at the properties (right click properties) | * Choose VMNet1 for host only mode (VMnet8 for NAT mode) connection and look at the properties (right click properties) | ||
* If you intend to use VMnet1 (which is the default) disable VMnet8 | * If you intend to use VMnet1 (which is the default) disable VMnet8 | ||
- | * Double click "Internet Protocol (TCP/IP)" | + | * Double click "Internet Protocol (TCP/IP)" (on Vista and windows 7 choose TCP/IPv4) |
* Make sure the first 3 parts of the ip address match that of your VM but not the last | * Make sure the first 3 parts of the ip address match that of your VM but not the last | ||
* If VM is in host only mode adjust the host side here (use this option by default) | * If VM is in host only mode adjust the host side here (use this option by default) | ||
Line 50: | Line 58: | ||
* Use putty to connect to newName-ux and login as root | * Use putty to connect to newName-ux and login as root | ||
* If you can't get that to work check the host name settings inside the VM networking | * If you can't get that to work check the host name settings inside the VM networking | ||
- | * If you still can't get it to work you can use the ip address of the machine which we recorded at the begining | + | * Add an entry for newName-ux and the corresponding ip address to the host machine's hosts file under (C:\Windows\System32\drivers\etc) |
+ | * To modify hosts file, you will need to run editor program as an administrator and hope the hosts file from inside that program | ||
+ | * If you still can't get it to work you can use the ip address of the machine which we recorded at the beginning | ||
* IP address is probably 192.168.80.200 | * IP address is probably 192.168.80.200 | ||