whatIf? Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Good TOOL Coding Practices ======
===== Create time sequences dynamically =====

There are many ways to create a time sequence dimension in an object:
  - myObj[t] = create (; dim=SEQ;time:1990:2000:1;year)
  - myObj[t] = create (; dimFrom1=myTimeObj[t]), where dimension t in myTimeObj is the time sequence 1990 to 2000
  - **myObj[t] = create (; dim=SEQ;time:$startYear:$endYear:1;year), where $startYear=1990 and $endYear=2000**

Method 1 causes problems if you later update the time sequence in the model.  If the time sequence changes, all code with hard-coded references the years in that sequence need to be updated in the procedure code, model views, and any TOOL scripts.  For larger models, this can be cumbersome and error-prone.

Method 2 causes problems if you later change the dimensions in myTimeObj.  For example, if you add a new dimension so to myTimeObj so that it is now myTimeObj[x,t], myObj in the above code would now be getting its dimension from x, which is now the first dimension, instead of t.  This error would most likely be detected during dimensional analysis, but if it somehow were to pass dimensional analysis then the error would be much harder to detect.  In either case, the code would have to be updated in the model procedures, model views, and TOOL scripts.

Method 3 is the recommended method for creating time sequences in an object.  Use [[tutorials:tool_quick_reference_card#tool_object_info|getobjinfo]] to derive the values for $startYear and $endYear as shown below
<code>
integer $startYear, $endYear
getobjinfo (myTimeObj[t], $startYear; info=sequenceStart, dim=time)
getobjinfo (myTimeObj[t], $endYear; info=sequenceEnd, dim=time)
myObj[t] = create (; dim=SEQ;time:$startYear:$endYear:1;year)
</code>

With this method changes to the time sequence will be automatically inherited because the sequence start and end years are derived dynamically.  Also, this method will still work if new dimensions are added to myTimeObj because the getobjinfo statement explicitly looks for the dimension time regardless of whether it is the first dimension.

===== Consolidate Objects Using Sum Instead of Insert =====
Object consolidation is when multiple objects are combined into one along a certain dimension.  In this example, we will create an object fuelUseAll[tm], where dimension tm is transportation mode (air, rail, car).  Assuming that we have calculated the fuel use for each mode so that we have the objects airFuelUse[], railFuelUse[], and carFuelUse[], we can create fuelUseAll[tm] in two ways:
  - <code>fuelUseAll[tm] = insert (airFuelUse[]; transMode:air)
fuelUseAll[tm] = insert (airFuelUse[]; transMode:rail)
fuelUseAll[tm] = insert (airFuelUse[]; transMode:car)</code>
  - <code>local airFuelUseAll[tm] = copyshape (fuelUseAll[tm])
local railFuelUseAll[tm] = copyshape (fuelUseAll[tm])
local carFuelUseAll[tm] = copyshape (fuelUseAll[tm])

airFuelUseAll[tm] = insert (airFuelUse[]; transMode:air)
railFuelUseAll[tm] = insert (airFuelUse[]; transMode:rail)
carFuelUseAll[tm] = insert (airFuelUse[]; transMode:car)

fuelUseAll[tm] = airFuelUseAll[tm] + railFuelUseAll[tm] + carFuelUseAll[tm]
</code>

Method 2 is the recommended method for consolidating objects.  The main advantage is that with method 2 if airFuelUse[], railFuelUse[], or carFuelUse[] were empty objects, this would be detected when trying to view fuelUseAll[tm].  With method 1, an empty object would not necessarily be detected when viewing fuelUseAll[tm].  If railFuelUse[] were empty, the values for rail in fuelUseAll would just become 0 after carFuelUse[] is inserted so the empty object would go undetected.

===== Variable Naming =====

Stub: best practices for variable naming, esp. locals FIXME

abbreviations, suffix vs. prefix convention?

^ Descriptor ^ Abbreviation ^
| share | Shr |
| intensity | Int |
| rate | Rt |
| efficiency | Eff |


Local variables in a procedure or view can proliferate as a result of reorder(), sum(), etc. operations. For code readability it is recommended that local variables created from a modelbase variables be named using the modelbase variable name followed by underscore and a meaningful descriptor. For example:

<code>
local population_tot[ts] = sum (population[s,ts,a]; dim1=sex, dim2=age)
</code>
whatIf? Wiki

User Tools

Site Tools

Page Tools
